|
:: مهندس ::
تاريخ التسجيل: Mar 2009
المشاركات: 32
|
|
نشاط [ doublemaged ]
قوة السمعة:0
|
|
02-03-2010, 08:32 PM
المشاركة 4
|
|
الاخ الفاضل
فيما يلى بعض برامج الات الشارب مع بعض الاختلاف الخفيف بين الة واخرى
2. Simulation code list
For sub codes marked with "*", only display is provided. (Cannot be
executed.)
Code
Function
Main Sub
1 1 Used to check the operation of the scanner unit
and its control circuit.
2 Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
2 1 Used to check the operation of the SPF unit and
the related circuit.
2 Used to check the operation of sensors and
detectors in the SPF unit and the related circuit.
3 Used to check the operation of the loads in the
SPF unit and the control circuits.
3 2 Used to check the operation of sensor and
detector in the finisher and the related circuit.
3 Used to check the operation of the load in the
finisher and the control circuit.
6 Used to adjust the finisher jogger position.
7 Used to adjust the offset tray operations.
11 Used to check the operation of the shifter.
4 2 Used to check the operation of sensor and
detector in the option tray and the related circuit.
3 Used to check the operation of the load in the
option tray and the control circuit.
5 1 Used to check the operation of the display, LCD in
the operation panel, and control circuit.
2 Used to check the operation of the heater lamp
and the control circuit.
3 Used to check the operation of the copy lamp and
the control circuit.
6 1 Used to check the operation of the loads (clutches
and solenoids) in the paper transport system and
the control circuit.
2 Used to check the operation of each fan motor and
its control circuit.
7 1 Used to set the aging operation conditions.
6 Used to set the cycle of intermittent aging.
8 Used to set the display of the warm-up time.
8 1 Used to check and adjust the operation of the
developing bias voltage in each copy mode and
the control circuit.
2 Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy
mode and the control circuit.
3 Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy
mode and the control circuit.
10 Used to check and adjust the operation of the
developing bias voltage in each printer mode and
the control circuit.
11 Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer
mode and the control circuit.
12 Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer
mode and the control circuit.
13 Used to check and adjust the operation of the
developing bias voltage in FAX mode and the
control circuit.
14 Used to check and adjust the operation of the main
charger grid voltage (high mode) in FAX mode and
the control circuit.
15 Used to check and adjust the operation of the main
charger grid voltage (low mode) in FAX mode and
the control circuit.
9 1 Used to check and adjust the operation of the load
(motor) in the duplex section and the control
circuit.
4 Used to adjust the rotation speed of the duplex
motor.
5 Used to adjust the switch back time of the duplex
motor.
10 0 Used to check the operation of the toner motor and
its control circuit.
14 0 Used to cancel excluding the self-diag U2/PF
troubles.
16 0 Used to cancel the self-diag U2 trouble.
17 0 Used to cancel the self diag "PF" trouble.
21 1 Used to set the maintenance cycle.
22 1 Used to check the counter value of each section.
2 Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing this
count value with the total counter value.)
3 Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
4 Used to check the total trouble (self diag) history.
5 Used to check the ROM version of each unit
(section).
7 Used to display the key operator code
8 Used to check the number of use of the staple, the
SPF, and scanning.
9 Used to check the number of use of each paper
feed section. (the number of prints)
10 Used to check the system configuration.
11 FAX related counter display
12 Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
19 Used to display the scanner mode counter.
24 1 Used to clear the misfeed counter, the misfeed
history, the trouble counter, and the trouble history.
(The counters are cleared after completion of
maintenance.)
2 Used to clear the number of use (the number of
prints) of each paper feed section.
3 Used to clear the number data of use of the staple,
the SPF and scanning.
4 Used to reset the maintenance counter.
5 Used to reset the developer counter. (The
developer counter of the DV unit which is installed
is reset.)
6 Used to reset the copy counter.
7 Used to clear the OPC drum (membrane
decrease) correction counter. (This simulation is
executed when the OPC drum is replaced.
9 Used to clear the printer print counter. (The
counter is cleared after completion of
maintenance.)
10 FAX related counter clear
15 Used to clear the scanner mode counter.
25 1 Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The
toner concentration sen
25 2 Used to make the initial setting of toner
concentration when replacing developer.
26 1 Used to set options. (This simulation is used to
make option setting when an option is installed.)
2 Used to detect the paper size.
3 Used to set the specifications of the auditor.
Setting must be made depending on the use
condition of the auditor.
5 Used to set the count mode of the total counter
and the maintenance counter.
6 Used to set the specifications depending on the
destination.
*10 Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL
board is installed.
*12 Used to input the Software Key for E-MAIL RIC.
*14 Used to input the Software Key for the PS
extension kit.
*18 Used to set enable/disable of toner save operation.
20 Used to set the job separator paper exit mode.
22 Used to set the specification (language display) for
the destination.
30 Used to set the operation mode for CE mark.
35 Used to set the mode of trouble memory.
36 Used to set whether to stop when the maintenance
life is reached.
37 Used to set whether to stop when the developer
life is reached.
38 Used to set whether to stop when the drum life is
reached.
41 Used to set whether the automatic magnification
ratio select (AMS) is always ON or not when
setting the pamphlet (center binding) function.
46 Used to set whether to meet with the output
direction of images regardless of the mode when
installing the finisher.
50 Used to set whether to use the black/white reverse
function.
54 Used to set the PWM duty (brightness) at the
center value of the LCD contrast.
57 Used to set the model code.
60 Used to set enable/disable of the FAX mode key
when FAX is not installed. (When FAX is installed,
the FAX mode is enabled regardless of this setup.)
27 1 Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
5 Used to enter the TAG No. of the copier.
30 1 Used to check the operation of sensors and
detectors in the sections other than the paper feed
section of the copier and the related circuit. (The
operation of sensors and detectors can be
monitored with the LCD.)
2 Used to check the operation of sensors and
detectors in the paper feed section and the related
circuits. (The operations of sensors and detectors
in the paper feed section can be monitored with
the LCD.)
40 1 Used to check the operation of the manual paper
feed tray paper size detector and the related
circuit. (The operation of the manual paper feed
tray paper size detector can be monitored with the
LCD.)
2 Used to adjust the manual paper feed tray paper
width detector detection level.
3 The AD conversion value of manual feed width
detection is displayed.
Code
Function
Main Sub
41 1 Used to check the document size detection photo
sensor.
2 Used to adjust the detection level of the document
size photo sensor.
3 Used to check the light reception level and the
detection level of the original size detection photo
sensor.
4 Used to adjust the detection level of OC 20
degrees.
43 1 Used to set the fusing temperature in each
operation mode.
10 Used to set the paper feed cycle for postcard.
44 1 Used to make various setups in each mode of
process control.
34 Used to adjust the transfer current value.
35 Correction temperature setup when correcting the
ambient temperature.
40 Used to set the rotating time before toner supply.
46 2 Used to adjust the copy exposure level.
*7 Used to adjust individually the copy exposure
level. (Super photo)
9 Used to adjust individually the copy exposure
level. (Character)
10 Used to adjust individually the copy exposure
level. (Character/Photo)
11 Used to adjust individually the copy exposure
level. (Photo)
12 FAX exposure level adjustment (batch)
13 to
16
FAX exposure level adjustment (individual)
18 Used to adjust the copy contrast. (Inclination)
19 Used to change the image quality in the exposure
mode.
20 Used to correct SPF exposure.
30 Used to set the AE limit.
48 1 Used to adjust the copy mode magnification ratio
(main scanning direction, sub scanning direction).
2 Used to adjust the scanner mode magnification
ratio (main/sub scanning direction).
3 Used to adjust the lead edge/sub scan
magnification ratio automatically.
8 FAX magnification ratio adjustment (read)
9 FAX magnification ratio adjustment (print)
10 FAX auto reduction magnification ratio (print).
50 1 Used to adjust the copy lead edge position.
5 Used to adjust the print image position (top
margin) on the print paper in the print mode.
6 Used to adjust the print image position (top
margin) on print paper in the copy mode. (SPF/
RSPF)
8 FAX lead edge adjustment (read)
9 FAX lead edge adjustment (print)
10 Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
12 Used to adjust the print image center position.
(Adjustment can be made for each document
mode.)
51 1 Used to adjust the OPC drum separation pawl ON
time.
2 Used to adjust the contact pressure of paper onto
the resist roller in each section (copier paper feed
section, duplex paper feed section, SPF paper
feed section). (When the print image position
varies greatly for the paper or when a lot of paper
jam troubles occur, the adjustment is required.)
51 8 Used to set to disable the operation of the
separation pawl of the photoconductor drum.
9 Used to adjust ON/OFF timing of the separation
voltage.
53 8 Used to adjust the mirror unit SPF scan position
automatically.
For the SPF scan position auto adjustment, the
mirror unit is shifted to 11mm before the SPF glass
cover edge and is moved by self-boost, and
images are scanned in each step, and the position
from the glass cover edge is automatically
detected.
[Adjustment value]
Default: 50 Setting range: 1 to 99
Adjustment unit 1 = about 0.127mm
61 1 Used to test the operation of the LSU.
63 1 Used to check the result of shading correction.
(The shading correction data are displayed.)
7 Used to adjust the SPF white correction start pixel
position automatically.
This adjustment is performed after the lens unit is
replaced.
64 1 Self print
Key input = 1
Self print is performed in the 2-by-4 mode (2-line
print and 4-line non-print).
Key input = 2
Grid print is performed. (1cm, 1-dot width WLT/A3
print (A3 main scan, WLT sub scan))
65 5 Used to check the operation panel.
66 1 FAX related soft SW setting
2 Initial set for the value of the FAX soft SW
3 FAX PWB memory check
4 Signal send mode
6 Printing the confidential password
7 Print the screen memory contents
8 Voice Message send
10 Image data memory clear
11 300bps signals send
13 Send test and adjustment of the dial pulse and
DTMF signal.
17 DTMF signal send
21 FAX information print
*22 Handset sound volume adjustment
30 Recognize TEL/LIU state change.
32 Receive data check
34 Communication time measurement display
37 Speaker sound volume adjustment
38 Time setting/check
41 CI signal check
50 FAST SRAM clear
51 Signal detection check
52 Pseudo-ringer check
53 SRAM backup
67 *11 Used to set the Select-IN signal.
*14 Used to check write/comparison of flash programs.
*17 Used to clear NVRAM.
*18 Used to clear the data area for FLASH ROM
Network Scanner Application.
*20 Used to check the network connection when a
scanner option is installed.
|
